eCatHub
All catalogs

NI CompactDAQ · Measurement systems

An independent 12-page guide to CompactDAQ chassis, C Series measurements, software, synchronization and project selection.

Published by: eCatHub · Independent editorial · Reuse license: CC-BY-4.0

The interface language does not change the original catalog content.

View PDF · Download PDF

Build a measurement system

NI CompactDAQ

01 / 12

Independent series guide

NI CompactDAQ · Measurement systems

An independent 12-page guide to CompactDAQ chassis, C Series measurements, software, synchronization and project selection.

cDAQ-9173 · © NI

© NI · cDAQ-9173

Sensors → modules → chassis → software

Define the decision the measurement supports

Keep model names unchanged

eCatHub · Independent series guide

01

From sensor to useful data

NI CompactDAQ

02 / 12

From sensor to useful data

Treat the signal path as a chain: sensor, input conditioning, conversion, timing, transfer and analysis. Write down the physical quantity and the required result before selecting a module or software interface.

cDAQ-9183 · laboratory · © NI

© NI · cDAQ-9183 · laboratory

Review checklist

01

Physical quantity and units

02

Expected range and signal bandwidth

03

Where the result will be consumed

eCatHub · Independent series guide

02

Chassis portfolio

NI CompactDAQ

03 / 12

Chassis portfolio

The chassis determines connectivity, available slots and system timing. Compare a small USB setup with an Ethernet installation near distributed sensors. Reserve capacity for planned channels rather than selecting on slot count alone.

cDAQ-9170 · © NI

© NI · cDAQ-9170

cDAQ-9173 · © NI

© NI · cDAQ-9173

cDAQ-9187 · © NI

© NI · cDAQ-9187

cDAQ-91701-slot USB-C chassis
cDAQ-91734-slot USB-C chassis
cDAQ-91878-slot Ethernet chassis
C SeriesChoose by measurement type and compatibility

eCatHub · Independent series guide

03

Match the measurement module

NI CompactDAQ

04 / 12

Match the measurement module

C Series includes different measurement and interface families. Temperature, strain and dynamic signals require different input characteristics. A connector that fits is not enough: check sensor excitation, range, isolation and the exact supported configuration.

NI-9223 · C Series · © NI

© NI · NI-9223 · C Series

Review checklist

01

Voltage / current / temperature

02

Strain / sound / vibration

03

Digital I/O and bus interfaces

eCatHub · Independent series guide

04

Timing and synchronization

NI CompactDAQ

05 / 12

Timing and synchronization

A common start event and a common time reference solve different problems. Specify acceptable alignment between signals, then verify the timing behavior of the selected chassis, module combination, driver and acquisition rates.

cDAQ-9187 · © NI

© NI · cDAQ-9187

Review checklist

01

Start trigger versus shared time

02

Single chassis versus multiple chassis

03

Verify behavior at the intended sample rates

eCatHub · Independent series guide

05

Choose the software workflow

NI CompactDAQ

06 / 12

Choose the software workflow

NI-DAQmx supports programmed acquisition workflows; FlexLogger offers a configuration-oriented route. Decide who maintains the application, how results are named and where data is stored. Bus interfaces may require their own drivers.

LabVIEW · CompactDAQ · © NI

© NI · LabVIEW · CompactDAQ

Review checklist

01

Programming versus configuration

02

File naming and channel metadata

03

Driver and operating-system compatibility

eCatHub · Independent series guide

06

Plan the physical installation

NI CompactDAQ

07 / 12

Plan the physical installation

Include cables, terminals, power, mounting and the host in the system plan. Separate the electrical design from the data workflow, then review both together. Confirm operating limits for the chosen parts rather than applying a family-wide rating.

CompactDAQ · DIN · © NI

© NI · CompactDAQ · DIN

Review checklist

01

Power and grounding plan

02

Cable identification and strain relief

03

Access for maintenance and replacement

eCatHub · Independent series guide

07

Example: mixed-sensor test bench

NI CompactDAQ

08 / 12

Example: mixed-sensor test bench

Illustrative brief: observe temperature and vibration during a motor test. Keep slow thermal trends and faster dynamic records distinguishable, while documenting how they are related in time. This is a planning example, not a validated hardware configuration.

cDAQ-9183 · laboratory · © NI

© NI · cDAQ-9183 · laboratory

Review checklist

01

Thermal channel list

02

Dynamic channel list

03

A documented time relationship

eCatHub · Independent series guide

08

A practical selection sequence

NI CompactDAQ

09 / 12

A practical selection sequence

Start with a channel inventory. Convert each sensor requirement into a module shortlist, then check chassis and software compatibility. Finish with accessories and a repeatable acceptance test before freezing the purchasing list.

cDAQ-9173 · © NI

© NI · cDAQ-9173

Review checklist

01

Inventory → shortlist → compatibility

02

Accessories → acceptance test

03

Record unresolved supplier questions

eCatHub · Independent series guide

09

Commissioning and data quality

NI CompactDAQ

10 / 12

Commissioning and data quality

Validate one channel before scaling the system. Record raw values, engineering units, timestamps and test conditions. Exercise a missing-sensor or disconnected-host case and document how the application reports incomplete data.

NI-9223 · C Series · © NI

© NI · NI-9223 · C Series

Review checklist

01

Baseline reading and units

02

Timestamp and file continuity

03

Disconnect and recovery observations

eCatHub · Independent series guide

10

Prepare a complete project brief

NI CompactDAQ

11 / 12

Prepare a complete project brief

A useful project brief records assumptions, unresolved questions and acceptance criteria as well as products. Duplicate this page and replace the prompts with your own requirements; keep the source document revision beside each confirmed decision.

Editable project worksheet

01

Signal, range and channel count

02

Timing, environment and storage

03

Owner, review date and acceptance test

Review checklist

Signal, range and channel countRecord for your project
Timing, environment and storageRecord for your project
Owner, review date and acceptance testRecord for your project

eCatHub · Independent series guide

11

Sources and reuse

NI CompactDAQ

12 / 12

Sources and reuse

The linked manufacturer pages are the reference for current product specifications. This publication contains original summaries and illustrative layouts, not reproduced manuals or product photographs. Translations are editorial examples and have not been approved by NI.

Official references · 2026-09-28

NI-01https://www.ni.com/en/shop/compactdaq.html
NI-02https://www.ni.com/zh-cn/shop/compactdaq.html
NI-03https://www.ni.com/en/shop/compactdaq/compactdaq-modules.html
NI-04https://www.ni.com/en/support/documentation/supplemental/21/time-based-synchronization-of-analog-input-c-series-modules-with.html
NI-05https://www.ni.com/pdf/product-flyers/compactdaq-systems.pdf

An eCatHub editorial demo, not an official manufacturer catalogue. Original text and diagrams: CC BY 4.0. Product names belong to their owners. Confirm specifications and compatibility in the linked official documents. Photographs and product illustrations © NI / Siemens; excluded from CC BY 4.0. See official references for image sources.

eCatHub · Independent series guide

12

Official references

NI-01 · CompactDAQ systems — official series overview

NI-02 · CompactDAQ 系统 — 官方中文产品线资料

NI-03 · C Series modules — official product families

NI-04 · Time-based synchronization of C Series analog inputs

NI-05 · CompactDAQ System Flyer — manufacturer PDF, external reading