Cover
EQIO
VPX-3304
PRODUCT MANUAL
3U VPX Four-Channel Isolated CAN Card
VPX communications and IO card · Industrial control · Rail transit
Appearance reference (generated from product photos); shipped units may differ.
Measurement and control, made easy.
Easy · Quick · Input · Output
EQIO.COM
Overview
EQIO
{{chapter}}
EQIO · VPX-3304 Product Manual
{{page}} / {{pages}}
01 OVERVIEW
3U VPX Four-Channel Isolated CAN Card
VPX communications and IO card · Industrial control · Rail transit · CAN data acquisition · VPX
VPX-3304 provides 4 independent isolated CAN I/O and 1-ch Gigabit Ethernet I/O, isolated isolation voltage rated 3500VDC, baud rate supports 5K to 1M, used for industrial bus attach and data HMI. Channel between and channel and system between respectively isolated, can multi item field bus aggregation to network interfaces. Front panel provides bus, network and power status indicator, facilitates chassis internal organize device connection, suited to industrial control, test equipment and field bus data acquisition.
3U VPX Four-Channel Isolated CAN Card product photo
Product appearance reference; shipped units may differ.
Key features
4-ch independent isolated CAN 5K–1M baud rate range Channel and system between 3500VDC isolated
1-ch Gigabit Ethernet Bus, network and power status indicator
Functions
EQIO
{{chapter}}
EQIO · VPX-3304 Product Manual
{{page}} / {{pages}}
02 FUNCTIONS
Functions and engineering value
4-ch independent CAN attach
Board provides 4 independent CAN I/O, can respectively connect different field bus, baud rate range 5K to 1M, including 666K configured with. Each channel rate, node address and application protocol should independent check, board provides communications attach resources, actual packet processing and equipment control logic from matching software implements.
Isolated and network data HMI
Channel between and channel and system between rated isolated isolation voltage 3500VDC, together with 1-ch Gigabit Ethernet used for organize field bus and host data HMI. Isolated isolation voltage is not the same as normal operation voltage, specific network communications protocol, cache and packet mapping method requires combined with matching driver note confirm.
Status observe and chassis integrates
CAN communications, network and power indicator facilitates observe run status, DEBUG UART used for debug maintenance. Board uses 12V power, typical power consumption low to 10W, 160 × 100mm board outline suited to match 3U VPX slot position; wide temperature capability still requires combined with complete chassis power and cooling conditions verification.
The functional notes explain the product’s role from published configuration. Optional functions, software and peripherals follow the project definition. Chip capability is not the same as implemented I/O.
Architecture
EQIO
{{chapter}}
EQIO · VPX-3304 Product Manual
{{page}} / {{pages}}
03 ARCHITECTURE
Signal and functional relationships
Functional block diagram
Express CAN, network and host management functional relationship, not limit communications direction or inferred internal CPU; protocol, driver and isolated used conditions must follow delivery note confirm.
Platform and I/O
This board 4-ch isolated CAN communications and network HMI main function, published data not gives processor or controller chip model. Signal via J30J connect field bus, Gigabit Ethernet via rear I/O connect system, host software management application data; isolated, debug and indicator function and communications protocol capability should respectively de.
Reading the diagram Solid lines show published functional relationships, not on-board buses, bridge chips or connector pins. Optional controllers, radios, storage and software follow the configuration and interface files.
SPECIFICATIONS
EQIO
{{chapter}}
EQIO · VPX-3304 Product Manual
{{page}} / {{pages}}
04 SPECIFICATIONS
Technical specifications
Compiled from published product data. Batch, I/O and environmental ratings follow the order confirmation.
Technical data
| Connector type | 4-channel completely independent isolated CAN I/O |
|---|---|
| Baud rate supports | 5K-1M (step 5K, including 666K) |
| Isolated isolation voltage | 3500VDC (channel between and channel and system between) |
| Power | Single 12V DC input, typical value power consumption: <10W |
| Communications management | Supports panel LED (CAN communications, network status, power), DEBUG signal (UART0-TX/RX) |
| Operating system | Linux, Windows (required custom driver program), Kylin OS, UnionTech UOS, Yihui SylixOS |
I/O and expansion
| Network interfaces | 1-ch Gigabit Ethernet (10/100/1000M adaptive) |
|---|---|
| J30J | - CAN0~ 3-channel H/L signal and GND; - EARTH; - DEBUG UART signal |
| P0 rear I/O | - 12V power input (multi pins and link); - system reset (SYS RST#); - GND |
| P1 rear I/O | - Gigabit network signal (GBE DA±/DB±/DC±/DD±); - GND |
Environmental conditions
| Operating temperature | Operating temperature: -40℃ ~ 85℃ (wide temperature), storage temperature: -55℃ ~ 105℃ |
|---|---|
| Relative humidity | 95%non-condensing |
Mechanical specifications and system requirements
| Specification | 160mm × 100mm, weight ≤ 300g (typical value, not including heatsink) |
|---|
Applications
EQIO
{{chapter}}
EQIO · VPX-3304 Product Manual
{{page}} / {{pages}}
05 APPLICATIONS
From product capability to applications
Multi bus equipment management
4 independent channel can respectively attach different equipment group CAN network, and via matching host software management packet and status. Design when each channel determine rate, terminal and grounding method, network side data package and acquisition cycle required based on actual driver and protocol bring-up, not cannot only from Ethernet rate calculate.
Industrial test data acquisition
Test bench can used multiple CAN channel at the same time connect different DUT equipment, software log packet and per application requirement compiled result. Published parameters not gives hardware time or channel synchronous accuracy, therefore related analysis capability should be actual driver and software confirm, not can other acquisition card function directly apply.
Rail device communications node
Match VPX chassis in, can used isolated CAN connect different field equipment, and from Gigabit Ethernet and system controller HMI. Whether meets specific rail application also requires check product standard and wiring conditions, −40–85℃temperature range is board-level specification, not can replace system environment and can reliability verification.
Integration checks
| CAN configured with | Confirm 4-ch independent channel rate, wiring and terminal; supports 5K–1M, step 5K and including 666K configured with. |
|---|---|
| Isolated and grounding | 3500VDC isolated isolation voltage metrics; check channel, EARTH and system relationship, not treat as can directly apply plus operation voltage. |
| Driver and protocol | Windows required custom driver; confirm Linux, Kylin, UOS or SylixOS adapts and network data package method. |
| Chassis power | 12V input, typical power consumption<10W; check P0 power reset, P1 Gigabit signal and −40–85℃operation conditions. |
Configuration
EQIO
{{chapter}}
EQIO · VPX-3304 Product Manual
{{page}} / {{pages}}
06 CONFIGURATION
Appearance, configuration and selection
3U VPX Four-Channel Isolated CAN Card multi-angle reference
Multi-angle reference (generated from product photos); shipped units may differ.
Configuration
Uses 12V DC input, typical power consumption low to 10W, operating temperature -40–85℃.
Selection guide
| Order confirmation | Batch, I/O and environmental ratings follow the order confirmation |
|---|---|
| Published data | Compiled from published product data; EQIO provides selection and system integration |
| Configuration talk | Share the application, I/O count, environment and software so a configuration can be proposed |
Request a quotation and selection support
Email lyping@eqio.com Phone +86 182 8191 2988 Web eqio.com
Brand
EQIO · VPX-3304 Product Manual
{{page}} / {{pages}}
EQIO Easy Quick Input Output
BRAND
Measurement and control, made easy.
EQIO product family concept
EQIO product family · concept rendering
Brand story
EQIO builds measurement and control products and systems. The name stands for Easy Quick Input Output: Easy is a clear structure that is quick to learn, Quick is a direct path to efficient delivery, and Input / Output is every link between the device under test and the control system. The soft single-cycle wave inside the Q links the brand to signals, acquisition and I/O. “Measurement and control, made easy” is our promise for every selection, integration and delivery.
What we do
| Products | Data acquisition, test instruments, control and I/O, modular platforms, software, cables |
|---|---|
| Systems | Configured to the measurand, channels, accuracy and software, from design to commissioning |
| Support | Selection advice, training, maintenance and calibration |
How we deliver
| Requirements | |
|---|---|
| Solution design | |
| Build & integration | |
| Factory test | |
| Delivery & training | |
| Ongoing support |
Email lyping@eqio.com Phone +86 182 8191 2988 Web EQIO.COM